”Dimensional Measurements” Laboratory


The ”Dimensional Measurements” Laboratory, manages – undertakes, preserves and disseminates through modern equipment the measurement unit of length, which is essential for the heavy industry, food, chemical, light and textile industry, medicine etc.


 

Main objectives of the laboratory are:

  • Assurance of uniformity, accuracy and traceability of measurements on the territory of the Republic of Moldova.
  • Management, maintenance, storage, preservance of measurement standards and of the equipment owned by the laboratory.
  • Research of the National Measurement Standards Base and of the equipment owned by the laboratory.
  • Storage, reproduction and dissemination of measurement units from national and reference measurement standards to the other standards and measuring instruments according to ierarchic schemes.
  • Participation in interlaboratory comparisons at international level for demonstration of laboratory measurement capabilities. 
  • High accuracy measurements performance.
  • Maintenance and continuous improvement of the quality management in the laboratory.
  • Development of calibration procedures based on international best practices.

Alexandru Mîrza - Head of laboratory

Tel: (373 22) 903 119

E-mail: dimensionale@inm.gov.md

National and reference measurement standards

ETN 06-15 National measurement standard of length unit from 0 to 20 m

Reference measurement standard of length unit from 0 to 1100 mm

Reference measurement standard of roughness unit 

Reference measurement standard of angle unit

Measurement capabilities and provided services

The ”Dimensional Measurements” Laboratory provides a wide range of services to the consumer. The activity of the laboratory is focused towards calibration of measuring instruments, ensuring the measurement uncertainty according to the measurement capabilities below:

    Table 1. Calibration areas accredited by MOLDAC

Equipment

Measurement range

Uncertainty

Unit

Ribbons and roulettes for length measuring

0 ÷ 20 m

0,18 mm +  7,6 · L · 10-6

m

Rulers

0 ÷ 4000 mm

0,06 mm

m

Gauge blocks

0,5mm ÷ 100 mm

Q[50; 0,84L] nm, L în mm

m

Digital micrometers v.d 0,001

0 ÷ 500 mm

1,3µm

m

 

Mechanic micrometers

v.d. 0,001

v.d. 0,01

 

1,3µm

2,6µm

Digital calipers v.d 0,01

0 ÷ 500 mm

9,4 µm

m

Mechanic calipers

v.d. 0,02

v.d. 0,05

v.d. 0,1

 

13,7 µm

30,0 µm

60,0 µm

 

    Table 2. Calibration areas based on self declaration

Equipment

Measurement range

Uncertainty

Unit

Metric rods

0 ÷ 4500 mm

0,4 mm

m

Dial comparators

v.d. 0,1 mm

v.d. 0,001 mm

v.d. 0,002 mm

0 ÷ 10 mm

 

8,0 µm

0,8 µm

0,8 µm

m

Protractors

Exterior

Interior

 

0 ÷ 360°

0 ÷ 180°

rad

Roughness measures

Ra

Rz

 

0,01 ÷ 10 µm

0,01 ÷ 50 µm

 

0,054 µm

0,084 µm

m

Control plates/tables

Δ± 1,5 mm

3 µm

m

Smooth ring type calibers

20 ÷ 150 mm

0,9 µm

m

Length measuring wheels

0 ÷ 9999,9 m

0,03%

m

Standard road

0 ÷ 3000 m

0,8 m

m

The calibrations performed by the laboratory are in line with the provisions of SM SR EN ISO/CEI 17025.

The laboratory provides trainings focused on correct performance of measurements and determination of their conventional values by applying correction factors and using measurement uncertainty. The training courses are offered in all subfields of the ”Dimensional Measurements” Laboratory.

 

 

Traceability routes
Traceability route of the length unitPublished: 03.05.2019